Created
February 12, 2026 22:54
-
-
Save lucmann/a5653d7f7792f7c84ec4e61ca1b865ef to your computer and use it in GitHub Desktop.
sd-v6.19-rc6.ok
This file contains hidden or bidirectional Unicode text that may be interpreted or compiled differently than what appears below. To review, open the file in an editor that reveals hidden Unicode characters.
Learn more about bidirectional Unicode characters
| [ 0.000000] Booting Linux on physical CPU 0x0000000000 [0x410fd034] | |
| [ 0.000000] Linux version 6.19.0-rc6-gc072629f05d7 (luc@vostro) (aarch64-linux-gnu-gcc (GCC) 15.1.0, GNU ld (GNU Binutils) 2.44) #3 SMP PREEMPT Thu Feb 12 07:40:01 CST 2026 | |
| [ 0.000000] KASLR disabled due to lack of seed | |
| [ 0.000000] Machine model: HiKey970 | |
| [ 0.000000] earlycon: pl11 at MMIO 0x00000000fff32000 (options '115200') | |
| [ 0.000000] printk: legacy bootconsole [pl11] enabled | |
| [ 0.000000] doing early options: loglevel='7' | |
| [ 0.000000] efi: EFI v2.6 by EDK II | |
| [ 0.000000] efi: MEMATTR=0xbe637018 MEMRESERVE=0xba405c18 | |
| [ 0.000000] OF: reserved mem: Reserved memory: No reserved-memory node in the DT | |
| [ 0.000000] Zone ranges: | |
| [ 0.000000] DMA [mem 0x0000000000000000-0x00000000ffffffff] | |
| [ 0.000000] DMA32 empty | |
| [ 0.000000] Normal [mem 0x0000000100000000-0x00000001bfffffff] | |
| [ 0.000000] Movable zone start for each node | |
| [ 0.000000] Early memory node ranges | |
| [ 0.000000] node 0: [mem 0x0000000000000000-0x00000000167fffff] | |
| [ 0.000000] node 0: [mem 0x0000000016988000-0x00000000209fffff] | |
| [ 0.000000] node 0: [mem 0x0000000020b00000-0x00000000320fffff] | |
| [ 0.000000] node 0: [mem 0x0000000032101000-0x000000008e0fffff] | |
| [ 0.000000] node 0: [mem 0x000000008e240000-0x00000000ba3effff] | |
| [ 0.000000] node 0: [mem 0x00000000ba3f0000-0x00000000ba3fffff] | |
| [ 0.000000] node 0: [mem 0x00000000ba400000-0x00000000ba438fff] | |
| [ 0.000000] node 0: [mem 0x00000000ba439000-0x00000000ba43cfff] | |
| [ 0.000000] node 0: [mem 0x00000000ba43d000-0x00000000ba44ffff] | |
| [ 0.000000] node 0: [mem 0x00000000ba450000-0x00000000ba68ffff] | |
| [ 0.000000] node 0: [mem 0x00000000ba690000-0x00000000bf65ffff] | |
| [ 0.000000] node 0: [mem 0x00000000bf660000-0x00000000bf69ffff] | |
| [ 0.000000] node 0: [mem 0x00000000bf6a0000-0x00000000bf6affff] | |
| [ 0.000000] node 0: [mem 0x00000000bf6b0000-0x00000000bf6fffff] | |
| [ 0.000000] node 0: [mem 0x00000000bf700000-0x00000000bfffffff] | |
| [ 0.000000] node 0: [mem 0x0000000100000000-0x00000001bfffffff] | |
| [ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x00000001bfffffff] | |
| [ 0.000000] On node 0, zone DMA: 392 pages in unavailable ranges | |
| [ 0.000000] On node 0, zone DMA: 256 pages in unavailable ranges | |
| [ 0.000000] On node 0, zone DMA: 1 pages in unavailable ranges | |
| [ 0.000000] On node 0, zone DMA: 320 pages in unavailable ranges | |
| [ 0.000000] cma: Reserved 64 MiB at 0x00000000b0000000 | |
| [ 0.000000] psci: probing for conduit method from DT. | |
| [ 0.000000] psci: PSCIv1.1 detected in firmware. | |
| [ 0.000000] psci: Using standard PSCI v0.2 function IDs | |
| [ 0.000000] psci: MIGRATE_INFO_TYPE not supported. | |
| [ 0.000000] psci: SMC Calling Convention v1.0 | |
| [ 0.000000] percpu: Embedded 23 pages/cpu s56088 r8192 d29928 u94208 | |
| [ 0.000000] Detected VIPT I-cache on CPU0 | |
| [ 0.000000] CPU features: detected: ARM erratum 845719 | |
| [ 0.000000] alternatives: applying boot alternatives | |
| [ 0.000000] Kernel command line: BOOT_IMAGE=/Image-hikey970-v6.19.0-rc2.gz earlycon=pl011,0xfff32000,115200 clk_ignore_unused=true console=tty0 console=ttyAMA6,115200n8 root=/dev/mmcblk0p2 rootwait rw debug loglevel=7 initcall_debug efi=noruntime dw_mmc.debug=1 | |
| [ 0.000000] printk: log_buf_len individual max cpu contribution: 4096 bytes | |
| [ 0.000000] printk: log_buf_len total cpu_extra contributions: 28672 bytes | |
| [ 0.000000] printk: log_buf_len min size: 16384 bytes | |
| [ 0.002910] rcu: Hierarchical SRCU implementation. | |
| [ 0.007781] rcu: Max phase no-delay instances is 1000. | |
| [ 0.013260] Timer migration: 1 hierarchy levels; 8 children per group; 1 crossnode level | |
| [ 0.022407] EFI runtime services will be disabled. | |
| [ 0.027531] smp: Bringing up secondary CPUs ... | |
| [ 0.032629] Detected VIPT I-cache on CPU1 | |
| [ 0.032698] CPU1: Booted secondary processor 0x0000000001 [0x410fd034] | |
| [ 0.033248] Detected VIPT I-cache on CPU2 | |
| [ 0.033282] CPU2: Booted secondary processor 0x0000000002 [0x410fd034] | |
| [ 0.033781] Detected VIPT I-cache on CPU3 | |
| [ 0.033813] CPU3: Booted secondary processor 0x0000000003 [0x410fd034] | |
| [ 0.034811] CPU features: detected: Spectre-v2 | |
| [ 0.034819] CPU features: detected: Spectre-v4 | |
| [ 0.034822] CPU features: detected: Spectre-BHB | |
| [ 0.034824] CPU features: detected: ARM erratum 858921 | |
| [ 0.034830] Detected VIPT I-cache on CPU4 | |
| [ 0.034860] arch_timer: Enabling local workaround for ARM erratum 858921 | |
| [ 0.034869] arch_timer: CPU4: Trapping CNTVCT access | |
| [ 0.034875] CPU4: Booted secondary processor 0x0000000100 [0x410fd092] | |
| [ 0.035378] Detected VIPT I-cache on CPU5 | |
| [ 0.035396] arch_timer: Enabling local workaround for ARM erratum 858921 | |
| [ 0.035402] arch_timer: CPU5: Trapping CNTVCT access | |
| [ 0.035406] CPU5: Booted secondary processor 0x0000000101 [0x410fd092] | |
| [ 0.035885] Detected VIPT I-cache on CPU6 | |
| [ 0.035905] arch_timer: Enabling local workaround for ARM erratum 858921 | |
| [ 0.035910] arch_timer: CPU6: Trapping CNTVCT access | |
| [ 0.035915] CPU6: Booted secondary processor 0x0000000102 [0x410fd092] | |
| [ 0.036442] Detected VIPT I-cache on CPU7 | |
| [ 0.036463] arch_timer: Enabling local workaround for ARM erratum 858921 | |
| [ 0.036467] arch_timer: CPU7: Trapping CNTVCT access | |
| [ 0.036472] CPU7: Booted secondary processor 0x0000000103 [0x410fd092] | |
| [ 0.036519] smp: Brought up 1 node, 8 CPUs | |
| [ 0.180965] SMP: Total of 8 processors activated. | |
| [ 0.185721] CPU: All CPU(s) started at EL2 | |
| [ 0.189891] CPU features: detected: 32-bit EL0 Support | |
| [ 0.195083] CPU features: detected: 32-bit EL1 Support | |
| [ 0.200284] CPU features: detected: CRC32 instructions | |
| [ 0.205482] CPU features: detected: PMUv3 | |
| [ 0.209571] alternatives: applying system-wide alternatives | |
| [ 0.216516] CPU features: emulated: Privileged Access Never (PAN) using TTBR0_EL1 switching | |
| [ 0.225259] Memory: 5991864K/6287580K available (17152K kernel code, 2190K rwdata, 9628K rodata, 3072K init, 361K bss, 226128K reserved, 65536K cma-reserved) | |
| [ 0.241823] devtmpfs: initialized | |
| [ 0.251871] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns | |
| [ 0.261769] posixtimers hash table entries: 4096 (order: 4, 65536 bytes, linear) | |
| [ 0.269369] futex hash table entries: 2048 (131072 bytes on 1 NUMA nodes, total 128 KiB, linear). | |
| [ 0.279388] 24608 pages in range for non-PLT usage | |
| [ 0.279393] 516128 pages in range for PLT usage | |
| [ 0.291699] DMI not present or invalid. | |
| [ 0.297497] NET: Registered PF_NETLINK/PF_ROUTE protocol family | |
| [ 0.304628] DMA: preallocated 1024 KiB GFP_KERNEL pool for atomic allocations | |
| [ 0.312038] DMA: preallocated 1024 KiB GFP_KERNEL|GFP_DMA pool for atomic allocations | |
| [ 0.320013] audit: initializing netlink subsys (disabled) | |
| [ 0.325630] audit: type=2000 audit(0.216:1): state=initialized audit_enabled=0 res=1 | |
| [ 0.336355] thermal_sys: Registered thermal governor 'fair_share' | |
| [ 0.342582] cpuidle: using governor ladder | |
| [ 0.346751] cpuidle: using governor menu | |
| [ 0.351083] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers. | |
| [ 0.358096] ASID allocator initialised with 65536 entries | |
| [ 0.365834] Serial: AMBA PL011 UART driver | |
| [ 0.370893] of_irq_parse_raw: /interrupt-controller@e82b0000:00000001,0000000d,0000ff08 | |
| [ 0.379132] of_irq_parse_raw: /interrupt-controller@e82b0000:00000001,0000000e,0000ff08 | |
| [ 0.387353] of_irq_parse_raw: /interrupt-controller@e82b0000:00000001,0000000b,0000ff08 | |
| [ 0.395572] of_irq_parse_raw: /interrupt-controller@e82b0000:00000001,0000000a,0000ff08 | |
| [ 0.404061] of_irq_parse_raw: /interrupt-controller@e82b0000:00000000,0000004a,00000004 | |
| [ 0.412370] of_irq_parse_raw: /interrupt-controller@e82b0000:00000000,0000004c,00000004 | |
| [ 0.420676] of_irq_parse_raw: /interrupt-controller@e82b0000:00000000,0000004f,00000004 | |
| [ 0.428979] of_irq_parse_raw: /interrupt-controller@e82b0000:00000000,00000054,00000004 | |
| [ 0.437255] of_irq_parse_raw: /interrupt-controller@e82b0000:00000000,00000055,00000004 | |
| [ 0.445530] of_irq_parse_raw: /interrupt-controller@e82b0000:00000000,00000056,00000004 | |
| [ 0.453808] of_irq_parse_raw: /interrupt-controller@e82b0000:00000000,00000057,00000004 | |
| [ 0.462089] of_irq_parse_raw: /interrupt-controller@e82b0000:00000000,00000058,00000004 | |
| [ 0.470366] of_irq_parse_raw: /interrupt-controller@e82b0000:00000000,00000059,00000004 | |
| [ 0.478643] of_irq_parse_raw: /interrupt-controller@e82b0000:00000000,0000005a,00000004 | |
| [ 0.486923] of_irq_parse_raw: /interrupt-controller@e82b0000:00000000,0000005b,00000004 | |
| [ 0.495203] of_irq_parse_raw: /interrupt-controller@e82b0000:00000000,0000005c,00000004 | |
| [ 0.503479] of_irq_parse_raw: /interrupt-controller@e82b0000:00000000,0000005d,00000004 | |
| [ 0.511757] of_irq_parse_raw: /interrupt-controller@e82b0000:00000000,0000005e,00000004 | |
| [ 0.520039] of_irq_parse_raw: /interrupt-controller@e82b0000:00000000,0000005f,00000004 | |
| [ 0.528319] of_irq_parse_raw: /interrupt-controller@e82b0000:00000000,00000060,00000004 | |
| [ 0.536598] of_irq_parse_raw: /interrupt-controller@e82b0000:00000000,00000061,00000004 | |
| [ 0.544879] of_irq_parse_raw: /interrupt-controller@e82b0000:00000000,00000062,00000004 | |
| [ 0.553157] of_irq_parse_raw: /interrupt-controller@e82b0000:00000000,00000063,00000004 | |
| [ 0.561439] of_irq_parse_raw: /interrupt-controller@e82b0000:00000000,00000064,00000004 | |
| [ 0.569718] of_irq_parse_raw: /interrupt-controller@e82b0000:00000000,00000065,00000004 | |
| [ 0.577999] of_irq_parse_raw: /interrupt-controller@e82b0000:00000000,00000066,00000004 | |
| [ 0.586283] of_irq_parse_raw: /interrupt-controller@e82b0000:00000000,00000067,00000004 | |
| [ 0.594562] of_irq_parse_raw: /interrupt-controller@e82b0000:00000000,00000068,00000004 | |
| [ 0.602842] of_irq_parse_raw: /interrupt-controller@e82b0000:00000000,00000069,00000004 | |
| [ 0.611122] of_irq_parse_raw: /interrupt-controller@e82b0000:00000000,0000006a,00000004 | |
| [ 0.619403] of_irq_parse_raw: /interrupt-controller@e82b0000:00000000,0000006b,00000004 | |
| [ 0.627682] of_irq_parse_raw: /interrupt-controller@e82b0000:00000000,0000006c,00000004 | |
| [ 0.635962] of_irq_parse_raw: /interrupt-controller@e82b0000:00000000,0000006d,00000004 | |
| [ 0.644243] of_irq_parse_raw: /interrupt-controller@e82b0000:00000000,0000006e,00000004 | |
| [ 0.652523] of_irq_parse_raw: /interrupt-controller@e82b0000:00000000,0000006f,00000004 | |
| [ 0.660804] of_irq_parse_raw: /interrupt-controller@e82b0000:00000000,0000008d,00000004 | |
| [ 0.669085] of_irq_parse_raw: /interrupt-controller@e82b0000:00000000,00000116,00000004 | |
| [ 0.677378] of_irq_parse_raw: /interrupt-controller@e82b0000:00000000,0000008b,00000004 | |
| [ 0.685782] of_irq_parse_raw: /interrupt-controller@e82b0000:00000000,0000008c,00000004 | |
| [ 0.694136] of_irq_parse_raw: /soc/gpio@fff0b000:00000001,00000001 | |
| [ 0.727344] HugeTLB: registered 1.00 GiB page size, pre-allocated 0 pages | |
| [ 0.734226] HugeTLB: 0 KiB vmemmap can be freed for a 1.00 GiB page | |
| [ 0.740562] HugeTLB: registered 32.0 MiB page size, pre-allocated 0 pages | |
| [ 0.747426] HugeTLB: 0 KiB vmemmap can be freed for a 32.0 MiB page | |
| [ 0.753761] HugeTLB: registered 2.00 MiB page size, pre-allocated 0 pages | |
| [ 0.760620] HugeTLB: 0 KiB vmemmap can be freed for a 2.00 MiB page | |
| [ 0.766955] HugeTLB: registered 64.0 KiB page size, pre-allocated 0 pages | |
| [ 0.773814] HugeTLB: 0 KiB vmemmap can be freed for a 64.0 KiB page | |
| [ 0.781849] ACPI: Interpreter disabled. | |
| [ 0.786909] iommu: Default domain type: Translated | |
| [ 0.791755] iommu: DMA domain TLB invalidation policy: strict mode | |
| [ 0.798631] SCSI subsystem initialized | |
| [ 0.803292] usbcore: registered new interface driver usbfs | |
| [ 0.808886] usbcore: registered new interface driver hub | |
| [ 0.814297] usbcore: registered new device driver usb | |
| [ 0.819828] mc: Linux media interface: v0.10 | |
| [ 0.824265] videodev: Linux video capture interface: v2.00 | |
| [ 0.829927] pps_core: LinuxPPS API ver. 1 registered | |
| [ 0.834943] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it> | |
| [ 0.844218] PTP clock support registered | |
| [ 0.849416] Advanced Linux Sound Architecture Driver Initialized. | |
| [ 0.856582] Bluetooth: Core ver 2.22 | |
| [ 0.860235] NET: Registered PF_BLUETOOTH protocol family | |
| [ 0.865603] Bluetooth: HCI device and connection manager initialized | |
| [ 0.872031] Bluetooth: HCI socket layer initialized | |
| [ 0.876964] Bluetooth: L2CAP socket layer initialized | |
| [ 0.882085] Bluetooth: SCO socket layer initialized | |
| [ 0.887531] vgaarb: loaded | |
| [ 0.890761] clocksource: Switched to clocksource arch_sys_counter | |
| [ 0.897436] VFS: Disk quotas dquot_6.6.0 | |
| [ 0.901418] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes) | |
| [ 0.909051] pnp: PnP ACPI: disabled | |
| [ 0.913719] NET: Registered PF_INET protocol family | |
| [ 0.918875] IP idents hash table entries: 131072 (order: 8, 1048576 bytes, linear) | |
| [ 0.930400] tcp_listen_portaddr_hash hash table entries: 4096 (order: 4, 65536 bytes, linear) | |
| [ 0.939107] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear) | |
| [ 0.946953] TCP established hash table entries: 65536 (order: 7, 524288 bytes, linear) | |
| [ 0.955256] TCP bind hash table entries: 65536 (order: 9, 2097152 bytes, linear) | |
| [ 0.964138] TCP: Hash tables configured (established 65536 bind 65536) | |
| [ 0.970908] UDP hash table entries: 4096 (order: 6, 262144 bytes, linear) | |
| [ 0.977949] UDP-Lite hash table entries: 4096 (order: 6, 262144 bytes, linear) | |
| [ 0.985629] NET: Registered PF_UNIX/PF_LOCAL protocol family | |
| [ 0.992519] PCI: CLS 0 bytes, default 64 | |
| [ 1.000617] kvm [1]: nv: 568 coarse grained trap handlers | |
| [ 1.006508] kvm [1]: IPA Size Limit: 40 bits | |
| [ 1.012551] kvm [1]: vgic interrupt IRQ9 | |
| [ 1.016549] kvm [1]: Hyp nVHE mode initialized successfully | |
| [ 1.024836] Initialise system trusted keyrings | |
| [ 1.029556] workingset: timestamp_bits=46 max_order=21 bucket_order=0 | |
| [ 1.036647] squashfs: version 4.0 (2009/01/31) Phillip Lougher | |
| [ 1.042660] fuse: init (API version 7.45) | |
| [ 1.046915] 9p: Installing v9fs 9p2000 file system support | |
| [ 1.053367] cryptd: max_cpu_qlen set to 1000 | |
| [ 1.098793] Key type asymmetric registered | |
| [ 1.102948] Asymmetric key parser 'x509' registered | |
| [ 1.107993] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 245) | |
| [ 1.115487] io scheduler mq-deadline registered | |
| [ 1.120080] io scheduler kyber registered | |
| [ 1.124180] io scheduler bfq registered | |
| [ 1.134410] pinctrl-single e896c000.pinmux: 459 pins, size 1836 | |
| [ 1.143867] pinctrl-single fff11000.pinmux: 463 pins, size 1852 | |
| [ 1.152704] pinctrl-single e896c800.pinmux: 459 pins, size 1836 | |
| [ 1.159380] pinctrl-single fc182000.pinmux: 10 pins, size 40 | |
| [ 1.165491] pinctrl-single fc182800.pinmux: 10 pins, size 40 | |
| [ 1.171647] pinctrl-single ff37e000.pinmux: 12 pins, size 48 | |
| [ 1.177777] pinctrl-single ff37e800.pinmux: 12 pins, size 48 | |
| [ 1.186542] pinctrl-single fff11800.pinmux: 463 pins, size 1852 | |
| [ 1.195735] of_irq_parse_raw: /interrupt-controller@e82b0000:00000000,00000054,00000004 | |
| [ 1.204849] pl061_gpio e8a0b000.gpio: PL061 GPIO chip registered | |
| [ 1.211065] of_irq_parse_raw: /interrupt-controller@e82b0000:00000000,00000055,00000004 | |
| [ 1.219813] pl061_gpio e8a0c000.gpio: PL061 GPIO chip registered | |
| [ 1.226015] of_irq_parse_raw: /interrupt-controller@e82b0000:00000000,00000056,00000004 | |
| [ 1.234723] pl061_gpio e8a0d000.gpio: PL061 GPIO chip registered | |
| [ 1.240928] of_irq_parse_raw: /interrupt-controller@e82b0000:00000000,00000057,00000004 | |
| [ 1.249635] pl061_gpio e8a0e000.gpio: PL061 GPIO chip registered | |
| [ 1.255844] of_irq_parse_raw: /interrupt-controller@e82b0000:00000000,00000058,00000004 | |
| [ 1.264547] pl061_gpio e8a0f000.gpio: PL061 GPIO chip registered | |
| [ 1.270751] of_irq_parse_raw: /interrupt-controller@e82b0000:00000000,00000059,00000004 | |
| [ 1.279465] pl061_gpio e8a10000.gpio: PL061 GPIO chip registered | |
| [ 1.285670] of_irq_parse_raw: /interrupt-controller@e82b0000:00000000,0000005a,00000004 | |
| [ 1.294567] pl061_gpio e8a11000.gpio: PL061 GPIO chip registered | |
| [ 1.300772] of_irq_parse_raw: /interrupt-controller@e82b0000:00000000,0000005b,00000004 | |
| [ 1.309480] pl061_gpio e8a12000.gpio: PL061 GPIO chip registered | |
| [ 1.315689] of_irq_parse_raw: /interrupt-controller@e82b0000:00000000,0000005c,00000004 | |
| [ 1.324405] pl061_gpio e8a13000.gpio: PL061 GPIO chip registered | |
| [ 1.330607] of_irq_parse_raw: /interrupt-controller@e82b0000:00000000,0000005d,00000004 | |
| [ 1.339336] pl061_gpio e8a14000.gpio: PL061 GPIO chip registered | |
| [ 1.345540] of_irq_parse_raw: /interrupt-controller@e82b0000:00000000,0000005e,00000004 | |
| [ 1.354270] pl061_gpio e8a15000.gpio: PL061 GPIO chip registered | |
| [ 1.360479] of_irq_parse_raw: /interrupt-controller@e82b0000:00000000,0000005f,00000004 | |
| [ 1.369193] pl061_gpio e8a16000.gpio: PL061 GPIO chip registered | |
| [ 1.375399] of_irq_parse_raw: /interrupt-controller@e82b0000:00000000,00000060,00000004 | |
| [ 1.384108] pl061_gpio e8a17000.gpio: PL061 GPIO chip registered | |
| [ 1.390312] of_irq_parse_raw: /interrupt-controller@e82b0000:00000000,00000061,00000004 | |
| [ 1.399034] pl061_gpio e8a18000.gpio: PL061 GPIO chip registered | |
| [ 1.405241] of_irq_parse_raw: /interrupt-controller@e82b0000:00000000,00000062,00000004 | |
| [ 1.413945] pl061_gpio e8a19000.gpio: PL061 GPIO chip registered | |
| [ 1.420155] of_irq_parse_raw: /interrupt-controller@e82b0000:00000000,00000063,00000004 | |
| [ 1.428868] pl061_gpio e8a1a000.gpio: PL061 GPIO chip registered | |
| [ 1.435077] of_irq_parse_raw: /interrupt-controller@e82b0000:00000000,00000064,00000004 | |
| [ 1.443813] pl061_gpio e8a1b000.gpio: PL061 GPIO chip registered | |
| [ 1.450024] of_irq_parse_raw: /interrupt-controller@e82b0000:00000000,00000065,00000004 | |
| [ 1.458738] pl061_gpio e8a1c000.gpio: PL061 GPIO chip registered | |
| [ 1.464944] of_irq_parse_raw: /interrupt-controller@e82b0000:00000000,00000066,00000004 | |
| [ 1.473664] pl061_gpio fff28000.gpio: PL061 GPIO chip registered | |
| [ 1.479869] of_irq_parse_raw: /interrupt-controller@e82b0000:00000000,00000067,00000004 | |
| [ 1.488589] pl061_gpio fff29000.gpio: PL061 GPIO chip registered | |
| [ 1.494805] of_irq_parse_raw: /interrupt-controller@e82b0000:00000000,00000068,00000004 | |
| [ 1.503528] pl061_gpio e8a1f000.gpio: PL061 GPIO chip registered | |
| [ 1.509735] of_irq_parse_raw: /interrupt-controller@e82b0000:00000000,00000069,00000004 | |
| [ 1.518458] pl061_gpio e8a20000.gpio: PL061 GPIO chip registered | |
| [ 1.524666] of_irq_parse_raw: /interrupt-controller@e82b0000:00000000,0000006a,00000004 | |
| [ 1.533456] pl061_gpio fff0b000.gpio: PL061 GPIO chip registered | |
| [ 1.539671] of_irq_parse_raw: /interrupt-controller@e82b0000:00000000,0000006b,00000004 | |
| [ 1.548382] pl061_gpio fff0c000.gpio: PL061 GPIO chip registered | |
| [ 1.554588] of_irq_parse_raw: /interrupt-controller@e82b0000:00000000,0000006c,00000004 | |
| [ 1.563315] pl061_gpio fff0d000.gpio: PL061 GPIO chip registered | |
| [ 1.569523] of_irq_parse_raw: /interrupt-controller@e82b0000:00000000,0000006d,00000004 | |
| [ 1.578245] pl061_gpio fff0e000.gpio: PL061 GPIO chip registered | |
| [ 1.584453] of_irq_parse_raw: /interrupt-controller@e82b0000:00000000,0000006e,00000004 | |
| [ 1.593172] pl061_gpio fff0f000.gpio: PL061 GPIO chip registered | |
| [ 1.599378] of_irq_parse_raw: /interrupt-controller@e82b0000:00000000,0000006f,00000004 | |
| [ 1.608096] pl061_gpio fff10000.gpio: PL061 GPIO chip registered | |
| [ 1.614305] of_irq_parse_raw: /interrupt-controller@e82b0000:00000000,0000008d,00000004 | |
| [ 1.623024] pl061_gpio fff1d000.gpio: PL061 GPIO chip registered | |
| [ 1.630057] ledtrig-cpu: registered to indicate activity on CPUs | |
| [ 1.657741] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled | |
| [ 1.667328] msm_serial: driver initialized | |
| [ 1.671598] SuperH (H)SCI(F) driver initialized | |
| [ 1.687040] brd: module loaded | |
| [ 1.697800] loop: module loaded | |
| [ 1.706602] tun: Universal TUN/TAP device driver, 1.6 | |
| [ 1.711995] CAN device driver interface | |
| [ 1.716658] e1000e: Intel(R) PRO/1000 Network Driver | |
| [ 1.721675] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. | |
| [ 1.727757] igb: Intel(R) Gigabit Ethernet Network Driver | |
| [ 1.727762] igb: Copyright (c) 2007-2014 Intel Corporation. | |
| [ 1.738928] igbvf: Intel(R) Gigabit Virtual Function Network Driver | |
| [ 1.745267] igbvf: Copyright (c) 2009 - 2012 Intel Corporation. | |
| [ 1.751339] sky2: driver version 1.30 | |
| [ 1.755408] PPP generic driver version 2.4.2 | |
| [ 1.759952] PPP BSD Compression module registered | |
| [ 1.764729] PPP Deflate Compression module registered | |
| [ 1.769852] PPP MPPE Compression module registered | |
| [ 1.774979] usbcore: registered new interface driver asix | |
| [ 1.780526] usbcore: registered new interface driver ax88179_178a | |
| [ 1.786772] usbcore: registered new interface driver cdc_ether | |
| [ 1.792757] usbcore: registered new interface driver net1080 | |
| [ 1.798561] usbcore: registered new interface driver cdc_subset | |
| [ 1.804632] usbcore: registered new interface driver zaurus | |
| [ 1.810367] usbcore: registered new interface driver cdc_ncm | |
| [ 1.816429] VFIO - User Level meta-driver version: 0.3 | |
| [ 1.824584] usbcore: registered new interface driver usb-storage | |
| [ 1.832028] mousedev: PS/2 mouse device common for all mice | |
| [ 1.837883] usbcore: registered new interface driver xpad | |
| [ 1.843436] usbcore: registered new interface driver usb_acecad | |
| [ 1.849503] usbcore: registered new interface driver aiptek | |
| [ 1.855223] usbcore: registered new interface driver hanwang | |
| [ 1.861025] usbcore: registered new interface driver kbtab | |
| [ 1.867846] i2c_dev: i2c /dev entries driver | |
| [ 1.873080] usbcore: registered new interface driver uvcvideo | |
| [ 1.880290] device-mapper: uevent: version 1.0.3 | |
| [ 1.885120] device-mapper: ioctl: 4.50.0-ioctl (2025-04-28) initialised: dm-devel@lists.linux.dev | |
| [ 1.894242] Bluetooth: HCI UART driver ver 2.3 | |
| [ 1.898739] Bluetooth: HCI UART protocol H4 registered | |
| [ 1.904458] sdhci: Secure Digital Host Controller Interface driver | |
| [ 1.910704] sdhci: Copyright(c) Pierre Ossman | |
| [ 1.915261] Synopsys Designware Multimedia Card Interface Driver | |
| [ 1.921828] sdhci-pltfm: SDHCI platform and OF driver helper | |
| [ 1.927671] of_irq_parse_raw: /interrupt-controller@e82b0000:00000000 | |
| [ 1.934268] ,0000008b,00000004 | |
| [ 1.937458] dwmmc_k3 ff37f000.dwmmc1: fifo-depth property not found, using value of FIFOTH register as default | |
| [ 1.947590] of_irq_parse_raw: /interrupt-controller@e82b0000 | |
| [ 1.953406] :00000000 | |
| [ 1.955702] ,00000116 | |
| [ 1.955703] 00000000 | |
| [ 1.955706] ,00000004 | |
| [ 1.957990] 00000000 | |
| [ 1.960280] | |
| [ 1.962562] | |
| [ 1.967847] fff0a000 | |
| [ 1.970446] ufshcd-hisi ff3c0000.ufs: ufshcd_populate_vreg: Unable to find vdd-hba-supply regulator, assuming enabled | |
| [ 1.981176] ufshcd-hisi ff3c0000.ufs: ufshcd_populate_vreg: Unable to find vcc-supply regulator, assuming enabled | |
| [ 1.981183] ufshcd-hisi ff3c0000.ufs: ufshcd_populate_vreg: Unable to find vccq-supply regulator, assuming enabled | |
| [ 1.981183] dwmmc_k3 ff37f000.dwmmc1: IDMAC supports 64-bit address mode. | |
| [ 1.981190] ufshcd-hisi ff3c0000.ufs: ufshcd_populate_vreg: Unable to find vccq2-supply regulator, assuming enabled | |
| [ 1.981218] ufshcd-hisi ff3c0000.ufs: invalid ref_clk setting = 3200000 | |
| [ 2.002019] dwmmc_k3 ff37f000.dwmmc1: Using internal DMA controller. | |
| [ 2.019407] dwmmc_k3 ff37f000.dwmmc1: Version ID is 270a | |
| [ 2.019438] dwmmc_k3 ff37f000.dwmmc1: DW MMC controller at irq 43,32 bit host data width,256 deep fifo | |
| [ 2.047618] dwmmc_k3 ff37f000.dwmmc1: Got CD GPIO | |
| [ 2.053675] scsi host0: ufshcd | |
| [ 2.066780] mmc_host mmc0: Bus speed (slot 0) = 400000Hz (slot req 400000Hz, actual 400000HZ div = 0) | |
| [ 2.105261] scsi 0:0:0:49488: Well-known LUN SAMSUNG KLUCG4J1ED-B0C1 0300 PQ: 0 ANSI: 6 | |
| [ 2.114462] hid: raw HID events driver (C) Jiri Kosina | |
| [ 2.115669] scsi 0:0:0:49476: Well-known LUN SAMSUNG KLUCG4J1ED-B0C1 0300 PQ: 0 ANSI: 6 | |
| ** 113 printk messages dropped ** | |
| [ 2.118768] scsi 0:0:0:0: Direct-Access SAMSUNG KLUCG4J1ED-B0C1 0300 PQ: 0 ANSI: 6 | |
| ** 1198 printk messages dropped ** | |
| [ 2.140380] sd 0:0:0:0: [sda] 1024 4096-byte logical blocks: (4.19 MB/4.00 MiB) | |
| [ 2.140443] sd 0:0:0:0: [sda] Write Protect is off | |
| [ 2.140552] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, supports DPO and FUA | |
| [ 2.140588] scsi 0:0:0:1: Direct-Access SAMSUNG KLUCG4J1ED-B0C1 0300 PQ: 0 ANSI: 6 | |
| [ 2.140600] sd 0:0:0:0: [sda] Preferred minimum I/O size 8192 bytes | |
| [ 2.140605] sd 0:0:0:0: [sda] Optimal transfer size 8192 bytes | |
| [ 2.141981] sd 0:0:0:1: [sdb] 1024 4096-byte logical blocks: (4.19 MB/4.00 MiB) | |
| [ 2.142037] sd 0:0:0:1: [sdb] Write Protect is off | |
| [ 2.142141] sd 0:0:0:1: [sdb] Write cache: enabled, read cache: enabled, supports DPO and FUA | |
| [ 2.142184] sd 0:0:0:1: [sdb] Preferred minimum I/O size 8192 bytes | |
| [ 2.142188] sd 0:0:0:1: [sdb] Optimal transfer size 8192 bytes | |
| [ 2.142239] scsi 0:0:0:2: Direct-Access SAMSUNG KLUCG4J1ED-B0C1 0300 PQ: 0 ANSI: 6 | |
| [ 2.143576] sd 0:0:0:2: [sdc] 2048 4096-byte logical blocks: (8.39 MB/8.00 MiB) | |
| [ 2.143630] sd 0:0:0:2: [sdc] Write Protect is off | |
| [ 2.143718] scsi 0:0:0:3: Direct-Access SAMSUNG KLUCG4J1ED-B0C1 0300 PQ: 0 ANSI: 6 | |
| [ 2.143733] sd 0:0:0:2: [sdc] Write cache: enabled, read cache: enabled, supports DPO and FUA | |
| [ 2.143786] sd 0:0:0:2: [sdc] Preferred minimum I/O size 8192 bytes | |
| [ 2.143790] sd 0:0:0:2: [sdc] Optimal transfer size 8192 bytes | |
| [ 2.145036] sd 0:0:0:3: [sdd] 15616000 4096-byte logical blocks: (64.0 GB/59.6 GiB) | |
| [ 2.145090] sd 0:0:0:3: [sdd] Write Protect is off | |
| [ 2.145190] sd 0:0:0:3: [sdd] Write cache: enabled, read cache: enabled, supports DPO and FUA | |
| [ 2.145233] sd 0:0:0:3: [sdd] Preferred minimum I/O size 8192 bytes | |
| [ 2.145236] sd 0:0:0:3: [sdd] Optimal transfer size 8192 bytes | |
| [ 2.226142] sd 0:0:0:0: [sda] Attached SCSI disk | |
| [ 2.321548] registered taskstats version 1 | |
| [ 2.323375] sd 0:0:0:2: [sdc] Attached SCSI disk | |
| [ 2.324508] GPT:Primary header thinks Alt. header is not at the end of the disk. | |
| [ 2.324512] GPT:7805956 != 15615999 | |
| [ 2.324515] GPT:Alternate GPT header not at the end of the disk. | |
| [ 2.324517] GPT:7805956 != 15615999 | |
| [ 2.324518] GPT: Use GNU Parted to correct GPT errors. | |
| [ 2.324537] sdd: sdd1 sdd2 sdd3 sdd4 sdd5 sdd6 sdd7 sdd8 sdd9 sdd10 sdd11 sdd12 sdd13 sdd14 sdd15 | |
| [ 2.325663] sd 0:0:0:3: [sdd] Attached SCSI disk | |
| [ 2.325736] Loading compiled-in X.509 certificates | |
| [ 2.330601] sd 0:0:0:1: [sdb] Attached SCSI disk | |
| [ 2.394757] mmc_host mmc0: Bus speed (slot 0) = 150000000Hz (slot req 200000000Hz, actual 150000000HZ div = 0) | |
| [ 2.417102] of_irq_parse_raw: /interrupt-controller@e82b0000:00000000,0000004a,00000004 | |
| [ 2.425767] fdf02000.serial: ttyAMA0 at MMIO 0xfdf02000 (irq = 46, base_baud = 0) is a PL011 rev2 | |
| [ 2.435108] of_irq_parse_raw: /interrupt-controller@e82b0000:00000000,0000004c,00000004 | |
| [ 2.443634] fdf03000.serial: ttyAMA2 at MMIO 0xfdf03000 (irq = 47, base_baud = 0) is a PL011 rev2 | |
| [ 2.452878] of_irq_parse_raw: /interrupt-controller@e82b0000:00000000,0000004f,00000004 | |
| [ 2.461384] fff32000.serial: ttyAMA6 at MMIO 0xfff32000 (irq = 48, base_baud = 0) is a PL011 rev2 | |
| [ 2.470438] printk: console [ttyAMA6] enabled | |
| [ 2.470438] printk: console [ttyAMA6] enabled | |
| [ 2.479208] printk: legacy bootconsole [pl11] disabled | |
| [ 2.479208] printk: legacy bootconsole [pl11] disabled | |
| [ 2.492684] of_irq_parse_raw: /interrupt-controller@e82b0000:00000000,0000008c,00000004 | |
| [ 2.492777] dwmmc_k3 fc183000.dwmmc2: fifo-depth property not found, using value of FIFOTH register as default | |
| [ 2.494910] dwmmc_k3 fc183000.dwmmc2: IDMAC supports 64-bit address mode. | |
| [ 2.494925] dwmmc_k3 fc183000.dwmmc2: Using internal DMA controller. | |
| [ 2.494930] dwmmc_k3 fc183000.dwmmc2: Version ID is 270a | |
| [ 2.494958] dwmmc_k3 fc183000.dwmmc2: DW MMC controller at irq 49,32 bit host data width,256 deep fifo | |
| [ 2.495167] mmc_host mmc1: card is non-removable. | |
| [ 2.582767] mmc_host mmc1: Bus speed (slot 0) = 400000Hz (slot req 400000Hz, actual 400000HZ div = 0) | |
| [ 2.595653] cfg80211: Loading compiled-in X.509 certificates for regulatory database | |
| [ 2.597216] Loaded X.509 cert 'sforshee: 00b28ddf47aef9cea7' | |
| [ 2.598355] Loaded X.509 cert 'wens: 61c038651aabdcf94bd0ac7ff06c7248db18c600' | |
| [ 2.598455] faux_driver regulatory: Direct firmware load for regulatory.db failed with error -2 | |
| [ 2.598468] cfg80211: failed to load regulatory.db | |
| [ 2.598704] clk: Not disabling unused clocks | |
| [ 2.598725] PM: genpd: Disabling unused power domains | |
| [ 2.598801] ALSA device list: | |
| [ 2.598805] No soundcards found. | |
| [ 2.601736] dwmmc_k3 fc183000.dwmmc2: card claims to support voltages below defined range | |
| [ 2.609181] check access for rdinit=/init failed: -2, ignoring | |
| [ 2.609326] Waiting for root device /dev/mmcblk0p2... | |
| [ 2.613370] mmc_host mmc1: Bus speed (slot 0) = 25000000Hz (slot req 25000000Hz, actual 25000000HZ div = 0) | |
| [ 2.616114] mmc1: new SDIO card at address 0001 | |
| [ 2.616488] of_irq_parse_raw: /soc/gpio@fff0b000:00000001,00000001 | |
| [ 2.616954] wl18xx_driver wl18xx.0.auto: Direct firmware load for ti-connectivity/wl1271-nvs.bin failed with error -2 | |
| [ 2.616988] wl18xx_driver wl18xx.0.auto: Direct firmware load for ti-connectivity/wl18xx-conf.bin failed with error -2 | |
| [ 2.616994] wlcore: ERROR could not get configuration binary ti-connectivity/wl18xx-conf.bin: -2 | |
| [ 2.616995] wlcore: WARNING falling back to default config | |
| [ 2.728803] mmc_host mmc1: Bus speed (slot 0) = 400000Hz (slot req 400000Hz, actual 400000HZ div = 0) | |
| [ 2.760145] mmc_host mmc1: Bus speed (slot 0) = 25000000Hz (slot req 25000000Hz, actual 25000000HZ div = 0) | |
| [ 2.849309] mmc_host mmc1: Bus speed (slot 0) = 400000Hz (slot req 400000Hz, actual 400000HZ div = 0) | |
| [ 2.880668] mmc_host mmc1: Bus speed (slot 0) = 25000000Hz (slot req 25000000Hz, actual 25000000HZ div = 0) | |
| [ 2.883971] dwmmc_k3 ff37f000.dwmmc1: tuning ok best_clksmpl 11 tuning_sample_flag bff3fff3 | |
| [ 2.883980] mmc0: new UHS-I speed SDR104 SDHC card at address aaaa | |
| [ 2.884298] mmcblk0: mmc0:aaaa SC16G 14.8 GiB | |
| [ 2.886979] mmcblk0: p1 p2 | |
| [ 3.083894] wlcore: wl18xx HW: 183x or 180x, PG 2.2 (ROM 0x11) | |
| [ 3.086393] wlcore: loaded | |
| [ 3.143596] EXT4-fs (mmcblk0p2): mounted filesystem 819c9d45-0e44-4a40-b07f-1792c8dc9b2f r/w with ordered data mode. Quota mode: none. | |
| [ 3.143680] VFS: Mounted root (ext4 filesystem) on device 179:2. | |
| [ 3.147303] devtmpfs: mounted | |
| [ 3.148266] Freeing unused kernel memory: 3072K | |
| [ 3.148418] Run /sbin/init as init process | |
| SELinux: Could not open policy file <= /etc/selinux/targeted/policy/policy.35: No such file or directory | |
| [ 3.432770] systemd[1]: System time before build time, advancing clock. | |
| [ 3.444481] systemd[1]: Failed to find module 'autofs4' | |
| [ 3.493282] systemd[1]: systemd 252.39-1~deb12u1 running in system mode (+PAM +AUDIT +SELINUX +APPARMOR +IMA +SMACK +SECCOMP +GCRYPT -GNUTLS +OPENSSL +ACL +BLKID +CURL +ELFUTILS +FIDO2 +IDN2 -IDN +IPTC +KMOD +LIBCRYPTSETUP +LIBFDISK +PCRE2 -PWQUALITY +P11KIT +QRENCODE +TPM2 +BZIP2 +LZ4 +XZ +ZLIB +ZSTD -BPF_FRAMEWORK -XKBCOMMON +UTMP +SYSVINIT default-hierarchy=unified) | |
| [ 3.493309] systemd[1]: Detected architecture arm64. | |
| Welcome to Debian GNU/Linux 12 (bookworm)! | |
| [ 3.542337] systemd[1]: Hostname set to <hikey970>. | |
| [ OK ] Created slice system-getty.slice - Slice /system/getty. | |
| [ OK ] Created slice system-modpr…lice - Slice /system/modprobe. | |
| [ OK ] Created slice system-seria… - Slice /system/serial-getty. | |
| [ OK ] Created slice system-wpa_s…0m - Slice /system/wpa_supplicant. | |
| [ OK ] Created slice user.slice - User and Session Slice. | |
| [ OK ] Started systemd-ask-passwo…quests to Console Directory Watch. | |
| [ OK ] Started systemd-ask-passwo… Requests to Wall Directory Watch. | |
| Expecting device dev-disk-…m - /dev/disk/by-uuid/9B52-C18F... | |
| Expecting device dev-ttyAMA6.device - /dev/ttyAMA6... | |
| Expecting device sys-subsy…sys/subsystem/net/devices/wlan0... | |
| [ OK ] Reached target cryptsetup.…get - Local Encrypted Volumes. | |
| [ OK ] Reached target integrityse…Local Integrity Protected Volumes. | |
| [ OK ] Reached target paths.target - Path Units. | |
| [ OK ] Reached target remote-fs.target - Remote File Systems. | |
| [ OK ] Reached target slices.target - Slice Units. | |
| [ OK ] Reached target swap.target - Swaps. | |
| [ OK ] Reached target veritysetup… - Local Verity Protected Volumes. | |
| [ OK ] Listening on systemd-initc… initctl Compatibility Named Pipe. | |
| [ OK ] Listening on systemd-journ…socket - Journal Audit Socket. | |
| [ OK ] Listening on systemd-journ…t - Journal Socket (/dev/log). | |
| [ OK ] Listening on systemd-journald.socket - Journal Socket. | |
| [ OK ] Listening on systemd-udevd….socket - udev Control Socket. | |
| [ OK ] Listening on systemd-udevd…l.socket - udev Kernel Socket. | |
| Mounting dev-hugepages.mount - Huge Pages File System... | |
| Mounting dev-mqueue.mountPOSIX Message Queue File System... | |
| Mounting sys-kernel-debug.… - Kernel Debug File System... | |
| Starting modprobe@configfs…m - Load Kernel Module configfs... | |
| Starting modprobe@dm_mod.s…[0m - Load Kernel Module dm_mod... | |
| Starting modprobe@drm.service - Load Kernel Module drm... | |
| Starting modprobe@efi_psto…- Load Kernel Module efi_pstore... | |
| Starting modprobe@fuse.ser…e - Load Kernel Module fuse... | |
| Starting modprobe@loop.ser…e - Load Kernel Module loop... | |
| Starting systemd-journald.service - Journal Service... | |
| Starting systemd-modules-l…rvice - Load Kernel Modules... | |
| Starting systemd-remount-f…nt Root and Kernel[ 4.433157] systemd-journald[1649]: /dev/kmsg buffer overrun, some messages lost. | |
| File Systems... | |
| Starting systemd-udev-trig…[0m - Coldplug All udev Devices... | |
| [ OK ] Mounted dev-hugepages.mount - Huge Pages File System. | |
| [ OK ] Mounted dev-mqueue.mount- POSIX Message Queue File System. | |
| [ OK ] Started systemd-journald.service - Journal Service. | |
| [ OK ] Mounted sys-kernel-debug.m…nt - Kernel Debug File System. | |
| [ OK ] Finished modprobe@configfs…[0m - Load Kernel Module configfs. | |
| [ OK ] Finished modprobe@dm_mod.s…e - Load Kernel Module dm_mod. | |
| [ OK ] Finished modprobe@drm.service - Load Kernel Module drm. | |
| [ OK ] Finished modprobe@efi_psto…m - Load Kernel Module efi_pstore. | |
| [ OK ] Finished modprobe@fuse.service - Load Kernel Module fuse. | |
| [ OK ] Finished modprobe@loop.service - Load Kernel Module loop. | |
| [ OK ] Finished systemd-modules-l…service - Load Kernel Modules. | |
| [ OK ] Finished systemd-remount-f…ount Root and Kernel File Systems. | |
| Mounting sys-fs-fuse-conne… - FUSE Control File System... | |
| Mounting sys-kernel-config…ernel Configuration File System... | |
| Starting systemd-journal-f…h Journal to Persistent Storage... | |
| Starting systemd-random-se…ice - Load/Save Random Seed... | |
| [ 4.699840] systemd-journald[1649]: Received client request to flush runtime journal. | |
| Starting systemd-sysctl.se…ce - Apply Kernel Variables... | |
| Starting systemd-sysusers.…rvice - Create System Users... | |
| [ OK ] Mounted sys-fs-fuse-connec…nt - FUSE Control File System. | |
| [ OK ] Mounted sys-kernel-config.… Kernel Configuration File System. | |
| [ OK ] Finished systemd-sysctl.service - Apply Kernel Variables. | |
| [ OK ] Finished systemd-sysusers.service - Create System Users. | |
| Starting systemd-tmpfiles-…ate Static Device Nodes in /dev... | |
| [ OK ] Finished systemd-udev-trig…e - Coldplug All udev Devices. | |
| Starting ifupdown-pre.serv…ynchronize boot up for ifupdown... | |
| [ 5.322320] systemd-journald[1649]: /dev/kmsg buffer overrun, some messages lost. | |
| [ 5.323169] systemd-journald[1649]: /dev/kmsg buffer overrun, some messages lost. | |
| [ 5.323647] systemd-journald[1649]: /dev/kmsg buffer overrun, some messages lost. | |
| [ 5.323915] systemd-journald[1649]: /dev/kmsg buffer overrun, some messages lost. | |
| [ OK ] Finished ifupdown-pre.serv… synchronize boot up for ifupdown. | |
| [ OK ] Finished systemd-tmpfiles-…reate Static Device Nodes in /dev. | |
| [ OK ] Reached target local-fs-pr…reparation for Local File Systems. | |
| Starting systemd-udevd.ser…ger for Device Events and Files... | |
| [ OK ] Finished systemd-journal-f…ush Journal to Persistent Storage. | |
| [ OK ] Started systemd-udevd.serv…nager for Device Events and Files. | |
| [ 5.888844] mmc_host mmc1: Bus speed (slot 0) = 400000Hz (slot req 400000Hz, actual 400000HZ div = 0) | |
| [ 5.920578] mmc_host mmc1: Bus speed (slot 0) = 25000000Hz (slot req 25000000Hz, actual 25000000HZ div = 0) | |
| [ OK ] Found device dev-disk-by\x…[0m - /dev/disk/by-uuid/9B52-C18F. | |
| [ OK ] Found device dev-ttyAMA6.device - /dev/ttyAMA6. | |
| [ OK ] Found device sys-subsystem… /sys/subsystem/net/devices/wlan0. | |
| Mounting boot.mount - /boot... | |
| [ OK ] Mounted boot.mount - /boot. | |
| [ OK ] Reached target local-fs.target - Local File Systems. | |
| Starting networking.service - Raise network interfaces... | |
| Starting systemd-tmpfiles-…te System Files and Directories... | |
| [ OK ] Listening on systemd-rfkil…l Switch Status /dev/rfkill Watch. | |
| [ OK ] Finished systemd-tmpfiles-…eate System Files and Directories. | |
| [ OK ] Started haveged.servicemon based on the HAVEGE algorithm. | |
| Starting systemd-rfkill.se…Load/Save RF Kill Switch Status... | |
| Starting systemd-update-ut…rd System Boot/Shutdown in UTMP... | |
| [ OK ] Started systemd-rfkill.ser…- Load/Save RF Kill Switch Status. | |
| [ OK ] Finished systemd-update-ut…cord System Boot/Shutdown in UTMP. | |
| [ OK ] Reached target sysinit.target - System Initialization. | |
| [ OK ] Started apt-daily.timer - Daily apt download activities. | |
| [ OK ] Started apt-daily-upgrade.… apt upgrade and clean activities. | |
| [ OK ] Started dpkg-db-backup.tim… Daily dpkg database backup timer. | |
| [ OK ] Started e2scrub_all.timeretadata Check for All Filesystems. | |
| [ OK ] Started fstrim.timer - Discard unused blocks once a week. | |
| [ OK ] Started logrotate.timer - Daily rotation of log files. | |
| [ OK ] Started systemd-tmpfiles-c… Cleanup of Temporary Directories. | |
| [ OK ] Reached target timers.target - Timer Units. | |
| [ OK ] Listening on dbus.socket- D-Bus System Message Bus Socket. | |
| [ OK ] Reached target sockets.target - Socket Units. | |
| [ OK ] Reached target basic.target - Basic System. | |
| [ OK ] Started cron.service -…kground program processing daemon. | |
| Starting dbus.service - D-Bus System Message Bus... | |
| Starting dhcpcd.serviceClient Daemon on all interfaces... | |
| Starting e2scrub_reap.serv…e ext4 Metadata Ch[ 6.705498] random: dbus-daemon: uninitialized urandom read (12 bytes read) | |
| eck Snapshots... | |
| [ OK ] Started rngd.service -…t entropy gathering daemon (rngd). | |
| [ 6.732690] random: dbus-daemon: uninitialized urandom read (12 bytes read) | |
| Starting systemd-logind.se…ice - User Login Management... | |
| [ OK ] Started wpa_supplicant@wla…pplicant daemon (interface wlan0). | |
| [ OK ] Started dbus.service - D-Bus System Message Bus. | |
| [ OK ] Finished networking.service - Raise network interfaces. | |
| [ 6.816481] random: dhcpcd: uninitialized urandom read (112 bytes read) | |
| Starting wpa_supplicant.service - WPA supplicant... | |
| [ OK ] Started systemd-logind.service - User Login Management. | |
| [ OK ] Started wpa_supplicant.service - WPA supplicant. | |
| [ OK ] Started dhcpcd.service…P Client Daemon on all interfaces. | |
| [ OK ] Reached target network.target - Network. | |
| Starting rc-local.servicem - /etc/rc.local Compatibility... | |
| Starting ssh.service - OpenBSD Secure Shell server... | |
| Starting systemd-user-sess…vice - Permit User Sessions... | |
| [ OK ] Finished systemd-user-sess…ervice - Permit User Sessions. | |
| [ 7.061368] mmc_host mmc1: Bus speed (slot 0) = 400000Hz (slot req 400000Hz, actual 400000HZ div = 0) | |
| [ OK ] Finished e2scrub_reap.serv…ine ext4 Metadata Check Snapshots. | |
| [ 7.092968] mmc_host mmc1: Bus speed (slot 0) = 25000000Hz (slot req 25000000Hz, actual 25000000HZ div = 0) | |
| [ 7.185362] mmc_host mmc1: Bus speed (slot 0) = 400000Hz (slot req 400000Hz, actual 400000HZ div = 0) | |
| [ 7.216848] mmc_host mmc1: Bus speed (slot 0) = 25000000Hz (slot req 25000000Hz, actual 25000000HZ div = 0) | |
| [ 7.462812] random: crng init done | |
| [ 7.462825] random: 4 urandom warning(s) missed due to ratelimiting | |
| [ 7.469065] systemd-journald[1649]: /dev/kmsg buffer overrun, some messages lost. | |
| [ 7.469095] systemd-journald[1649]: /dev/kmsg buffer overrun, some messages lost. | |
| [ 7.470738] systemd-journald[1649]: /dev/kmsg buffer overrun, some messages lost. | |
| [ 7.470782] systemd-journald[1649]: /dev/kmsg buffer overrun, some messages lost. | |
| ** 383 printk messages dropped ** | |
| ** 200 printk messages dropped ** | |
| ** 198 printk messages dropped ** | |
| ** 214 printk messages dropped ** | |
| ** 206 printk messages dropped ** | |
| ** 233 printk messages dropped ** | |
| ** 333 printk messages dropped ** | |
| ** 353 printk messages dropped ** | |
| ** 345 printk messages dropped ** | |
| ** 319 printk messages dropped ** | |
| ** 99 printk messages dropped ** | |
| ** 32 printk messages dropped ** | |
| ** 25 printk messages dropped ** | |
| ** 1 printk messages dropped ** | |
| ** 17 printk messages dropped ** | |
| ** 33 printk messages dropped ** | |
| [ 7.523776] systemd-journald[1649]: /dev/kmsg buffer overrun, some messages lost. | |
| ** 72 printk messages dropped ** | |
| ** 27 printk messages dropped ** | |
| [ OK ] Finished systemd-random-se…rvicerintk messages dropped ** | |
| ** 29 printk messages dropped ** | |
| ** 20 printk messages dropped ** | |
| ** 16 printk messages dropped ** | |
| ** 22 printk messages dropped ** | |
| ** 34 printk messages dropped ** | |
| ** 14 printk messages dropped ** | |
| ** 11 printk messages dropped ** | |
| ** 16 printk messages dropped ** | |
| ** 42 printk messages dropped ** | |
| ** 305 printk messages dropped ** | |
| ** 2 printk messages dropped ** | |
| [ 7.616362] wlcore: firmware booted (Rev 8.9.0.0.83) | |
| [ 7.631833] net_ratelimit: 20 callbacks suppressed | |
| [FAILED] Failed to start ssh.servic…[0m - OpenBSD Secure Shell server. | |
| See 'systemctl status ssh.service' for details. | |
| [ OK ] Stopped ssh.service - OpenBSD Secure Shell server. | |
| Starting ssh.service - OpenBSD Secure Shell server... | |
| [FAILED] Failed to start ssh.servic…[0m - OpenBSD Secure Shell server. | |
| See 'systemctl status ssh.service' for details. | |
| [ OK ] Stopped ssh.service - OpenBSD Secure Shell server. | |
| Starting ssh.service - OpenBSD Secure Shell server... | |
| [FAILED] Failed to start ssh.servic…[0m - OpenBSD Secure Shell server. | |
| See 'systemctl status ssh.service' for details. | |
| [ OK ] Stopped ssh.service - OpenBSD Secure Shell server. | |
| Starting ssh.service - OpenBSD Secure Shell server... | |
| [FAILED] Failed to start ssh.servic…[0m - OpenBSD Secure Shell server. | |
| See 'systemctl status ssh.service' for details. | |
| [ OK ] Stopped ssh.service - OpenBSD Secure Shell server. | |
| Starting ssh.service - OpenBSD Secure Shell server... | |
| [FAILED] Failed to start ssh.servic…[0m - OpenBSD Secure Shell server. | |
| See 'systemctl status ssh.service' for details. | |
| [ 9.338009] rc.local[3208]: Creating SSH2 RSA key; this may take some time ... | |
| [ 9.355766] rc.local[3287]: 3072 SHA256:MnZphO7CPH3+jk9xfHStsR/GhI45wBbQbaaXCW3sqi0 root@hikey970 (RSA) | |
| [ 9.379459] rc.local[3208]: Creating SSH2 ECDSA key; this may take some time ... | |
| [ 9.397504] rc.local[3293]: 256 SHA256:wPQg49Fg0C+uBILCIgeef3aebz9YphMSerCB32FLJAk root@hikey970 (ECDSA) | |
| [ 9.412634] rc.local[3208]: Creating SSH2 ED25519 key; this may take some time ... | |
| [ OK ] Stopped ssh.service - OpenBSD Secure Shell server. | |
| [ 9.427260] rc.local[3297]: 256 SHA256:M/WH4EGS+xDPiCvuRwDT3aqjSbnX9Ba5Lb2LfrKdvjU root@hikey970 (ED25519) | |
| [FAILED] Failed to start ssh.servic…[0m - OpenBSD Secure Shell server. | |
| See 'systemctl status ssh.service' for details. | |
| [ 11.122507] rc.local[3346]: rescue-ssh.target is a disabled or a static unit not running, not starting it. | |
| Starting ssh.service - OpenBSD Secure Shell server... | |
| [ OK ] Started ssh.service - OpenBSD Secure Shell server. | |
| [ 11.988088] wlan0: authenticate with 60:3a:7c:52:9c:1f (local address=c8:df:84:51:a3:37) | |
| [ 11.988095] wlan0: send auth to 60:3a:7c:52:9c:1f (try 1/3) | |
| [ 12.013687] wlan0: authenticated | |
| [ 12.018763] wlan0: associate with 60:3a:7c:52:9c:1f (try 1/3) | |
| [ 12.032488] wlan0: RX AssocResp from 60:3a:7c:52:9c:1f (capab=0x1411 status=0 aid=1) | |
| [ 12.041400] wlan0: associated | |
| [ 12.204254] wlcore: Association completed. | |
| [ 12.619838] rc.local[3379]: ssh.socket is a disabled or a static unit not running, not starting it. | |
| [ OK ] Started rc-local.service - /etc/rc.local Compatibility. | |
| [ OK ] Started serial-getty@ttyAM…ice - Serial Getty on ttyAMA6. | |
| [ OK ] Reached target getty.target - Login Prompts. | |
| [ OK ] Reached target multi-user.target - Multi-User System. | |
| [ OK ] Reached target graphical.target - Graphical Interface. | |
| Starting systemd-update-ut… Record Runlevel Change in UTMP... | |
| [ OK ] Finished systemd-update-ut… - Record Runlevel Change in UTMP. | |
| Debian GNU/Linux 12 hikey970 ttyAMA6 | |
| hikey970 login: hi | |
| Password: | |
| Linux hikey970 6.19.0-rc6-gc072629f05d7 #3 SMP PREEMPT Thu Feb 12 07:40:01 CST 2026 aarch64 | |
| * Image Support: https://github.com/lucmann/hikey970-debian-image | |
| The programs included with the Debian GNU/Linux system are free software; | |
| the exact distribution terms for each program are described in the | |
| individual files in /usr/share/doc/*/copyright. | |
| Debian GNU/Linux comes with ABSOLUTELY NO WARRANTY, to the extent | |
| permitted by applicable law. | |
| hi@hikey970:~$ [ 34.110808] ldo3: disabling | |
| [ 34.110847] ldo4: disabling | |
| [ 100.072605] systemd-journald[1649]: /dev/kmsg buffer overrun, some messages lost. | |
| [ 154.124108] systemd-journald[1649]: /dev/kmsg buffer overrun, some messages lost. | |
| hi@hikey970:~$ | |
| hi@hikey970:~$ | |
| hi@hikey970:~$ [ 263.153045] systemd-journald[1649]: /dev/kmsg buffer overrun, some messages lost. | |
| [ 263.161045] systemd-journald[1649]: /dev/kmsg buffer overrun, some messages lost. | |
| hi@hikey970:~$ [ 263.323014] systemd-journald[1649]: /dev/kmsg buffer overrun, some messages lost. | |
| hi@hikey970:~$ | |
| hi@hikey970:~$ | |
| hi@hikey970:~$ |
Sign up for free
to join this conversation on GitHub.
Already have an account?
Sign in to comment